收藏本站
Table 2. Operating Characteristics
Unless otherwise noted: - 40°C < T A < 85°C, 2.2 V < V DD < 3.6 V, Acceleration = 0g, Loaded output (1)
Characteristic
Symbol
Min
Typ
Max
Unit
Operating Range
(2)
Supply Voltage (3)
Supply Current (4)
Supply Current at Sleep Mode (4)
Operating Temperature Range
V DD
I DD
I DD
T A
2.2
—
—
-40
2.8
400
3
—
3.6
600
10
+85
V
μ A
μ A
°C
Acceleration Range, X-Axis, Y-Axis
g-Select: 0
g-Select: 1
g FS
g FS
—
—
±4
±9
—
—
g
g
Output Signal
Zero g (T A = 25°C, V DD = 2.8 V) (5), (6)
Zero g (7)
V OFF
V OFF , T A
1.316
-2.0
1.4
±0.5
1.484
+2.0
V
mg/°C
Sensitivity (T A = 25°C, V DD = 2.8 V)
4g
9g
Sensitivity (4)
S 4g
S 9g
S,T A
289.5
75.2
-0.0075
308
83.6
±0.002
326.5
91.9
+0.0075
mV/g
mV/g
%/°C
Bandwidth Response
XY
Output Impedance
f -3dBXY
Z O
—
24
400
32
—
40
Hz
k Ω
Noise
Power Spectral Density RMS (0.1 Hz – 1 kHz) (4)
n PSD
—
350
—
μ g/ Hz
Control Timing
Power-Up Response Time (8)
Enable Response Time (9)
t RESPONSE
t ENABLE
—
—
1.0
0.5
2.0
2.0
ms
ms
Sensing Element Resonant Frequency
XY
Internal Sampling Frequency
f GCELLXY
f CLK
—
—
6.0
11
—
—
kHz
kHz
Output Stage Performance
Full-Scale Output Range (I OUT = 3 μA)
Nonlinearity, X OUT , Y OUT
Cross-Axis Sensitivity (10)
V FSO
NL OUT
V XY
V SS +0.1
-1.0
-5.0
—
—
—
V DD –0.1
+1.0
+5.0
V
%FSO
%
1. For a loaded output, the measurements are observed after an RC filter consisting of an internal 32 k Ω resistor and an external 3.3 nF capacitor
(recommended as a minimum to filter clock noise) on the analog output for each axis and a 0.1 μ F capacitor on V DD - GND. The output sensor
bandwidth is determined by the Capacitor added on the output. f = 1/2 π * (32 x 10 3 ) * C. C = 3.3 nF corresponds to BW = 1507HZ, which is
the minimum to filter out internal clock noise.
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 2.2 and 3.6 V, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the device
may operate as a linear device but is not guaranteed to be in calibration.
4. This value is measured with g-Select in 4g mode.
5. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
will increase above V DD /2. For negative acceleration, the output will decrease below V DD /2.
6. For optimal 0g offset performance, adhere to AN3484 and AN3447.
7.Product Performance will not exceed this minimum level, however, measurement over time will not be equal to time zero measurements for
this specific parameter.
8. The response time between 10% of full scale V DD input voltage and 90% of the final operating output voltage.
9. The response time between 10% of full scale Sleep Mode input voltage and 90% of the final operating output voltage.
10. A measure of the device’s ability to reject an acceleration applied 90° from the true axis of sensitivity
MMA6331L
Sensors
Freescale Semiconductor
3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MMA6341LT IC ACCELER 3G/8G XY-AXIS 14LGA
MMA6361LT IC ACCELER 1.5G XY-AXIS 14LGA
MMA6527KW IC ACCELEROMETER XY AXIS 16QFN
MMA6556KW IC ACCELEROMETER X AXIS 16QFN
MMA6826AKW IC ACCELEROMETER XY AXIS 16QFN
MMA6854KW IC ACCELEROMETER X AXIS 16QFN
MMA7331LR2 ACCELEROMETER 4G XYZ ENH 14-LGA
MMA8451QT IC ACCELEROMETER 3AXIS 16QFN
相关代理商/技术参数
MMA6341LR1 功能描述:加速计 - 板上安装 3g-8g XY-Axis Low g RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA6341LR2 功能描述:加速计 - 板上安装 3G-9G XY-AXIS LOW G RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA6341LT 功能描述:加速计 - 板上安装 3G-9G XY-AXIS LOW G RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA6361L 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:?±1.5g, ?±6g Two Axis Low-g Micromachined Accelerometer
MMA6361LR1 功能描述:加速计 - 板上安装 1.5 XY LGA 14 LD ENH RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA6361LR2 功能描述:加速计 - 板上安装 1.5 XY LGA 14 LD ENH RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA6361LT 功能描述:加速计 - 板上安装 1.5G XY LGA 14 LDS ENH RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA6519KW 功能描述:加速计 - 板上安装 XY-AXIS 80/ 80G RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C